Dimplex BFSL33 Guia de Instalação

Installation GuideModelBFSL33IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to install or use this replace. For your sa

10SECTION D: MAIN POWER WALL SWITCH WIRING Wi r i n g fo r 240 vo l T! NOTE: Before installing the unit you must have the following wires in-stalled

11240 vo l T Ma i n Wa l l sW i T C h Wi r i n g di a g r a M FIREPLACE JUNCTION BOX 240 V POWER SUPPLY (BREAKER PANEL) WHITE - N RED – L2 BLAC

12Wi r i n g fo r 120 vo l T! NOTE: Before installing the unit have the following wires installed:A 2 conductor wire with ground (3 wires total) fro

13120 vo l T Ma i n Wa l l sW i T C h Wi r i n g di a g r a M FIREPLACE JUNCTION BOX 120 V POWER SUPPLY (BREAKER PANEL) WHITE - N RED – L2 BL

14Wi r i n g fo r 120 vo l T no he a T in s T a l l a T i o n! NOTE: Before installing the unit have the following wires installed:A 2 conductor w

15120 vo l T Ma i n Wa l l sW i T C h Wi r i n g di a g r a M - no he a T in s T a l l a T i o n FIREPLACE JUNCTION BOX 120 V POWER SUPPLY (

16SECTION E: he a T e r Wa l l sW i T C h Wi r i n g fo r 120/240 vo l T! NOTE: Before installing the unit complete the following:Install main

17he a T e r Wa l l sW i T C h Wi r i n g di a g r a M fo r 120/240 vo l T(See Section C or Section D For Main Power Connection) FIREPLACE JUNCT

18Wa l l Mo u n T i n g Th e r M o s T a T Wi r i n g fo r 120/240 vo l T! NOTE: Before installing the unit complete the following:Install main p

19Wa l l Mo u n T e d Th e r M o s T a T Wi r i n g di a g r a M fo r 120/240 vo l T(See Section C or Section D For Main Power Connection) FIREP

Ta b l e o f Co n T e n T sli s T i ng a n d Co d e ap p r o v a l s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Mo

20fl a M e o v e r r i d e sW i T C h Wi r i n g fo r 120/240 vo l TNOT AVAILABLE WITH NO HEAT INSTALLATION! NOTE: The replace can be wired to h

21fl a M e ov e r r i d e Wa l l sW i T C h Wi r i n g di a g r a M fo r 120/240 vo l T(See Section C or Section D For Main Power Connection)NO

UNIT INTERNAL WIRING DIAGRAMDimplex North America Limited1367 Industrial RoadCambridge, ONCanada N1R 7G8© 2011 Dimplex North America LimitedNo s

LISTING AND CODE APPROVALSThe BF series replaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for xed and location

4TRIM MOUNTINGThis replace comes with three trim pieces, top and two sides. The top piece is secured with screws at either end and one in the middle

5SECTION A: FRAMING DIMENSIONSRough-In Framing DimensionsFirebox DimensionsRough-In Corner FramingThis replace is a zero clearance design. No combus

6! IMPORTANT: Ensure that the incoming power supply volt-age matches the setting of the voltage selector switch.! NOTE: The voltage selector switch i

7SECTION C: FACTORY SETTING WIRING240 vo l T in s T a l l a T i o n(Without Main Power Wall Switch)! IMPORTANT: The unit is factory congured for 2

8120 vo l T in s T a l l a T i o n(Without Main Power Wall Switch)! IMPORTANT: The unit is factory congured for 208/240 volt operation! NOTE: Use 2

9120 vo l T in s T a l l a T i o n - no he a T in s T a l l a T i o n(Without Main Power Wall Switch & No Heat Installation)! IMPORTANT: The u