Models with Timer
DXLWP400TI, DXLWP800TI N & ARLWP800TI
Set the I - - O slide switch on the timer
(Fig. 3) to:
Position O - Heating Off
Position I - Manual operation
This setting allows power to the heater
uninterrupted by the timer settings. The
heat selector switch will control the output
(see ‘Using the heater’).
Position - ‘Auto’ operation
DO NOT disconnect this heater from the
mains supply unless it is being taken out
of use (e.g. in summer or for storage),
otherwise the timer clock will stop.
Setting the time of day
To set the time of day, rotate the timer dial
clockwise (indicated by the arrow) until
the correct time of day is opposite the
reference mark
(see Fig. 4).
The 24-hour clock is used: e.g. time shown for 3 pm is ‘15’
(15:00hrs).
Setting the ‘Auto’ ON and OFF times
To set the timer:
1. Using your fi nger tip or the tip of a
pencil, push in as many segments as
necessary around the dial, according to
the times you don’t require heat – see
Fig. 4. Each segment pushed in switches
the heater OFF for that part of the hour.
All other segments will be ON. For
example, Fig. 5 shows the timer set to
switch the heater ON between 7 am and
9 am and between 4 pm and 9.30 pm .
2. You can select as many ON periods as you like, within the
24-hour day. The settings will repeat every day until changed.
3. To change ON and OFF times, simply push in any ‘ON’ segments
you wish to cancel and pull out new ‘ON’ segments as required.
Switching to auto
Set the heat selector and thermostat for the heat output required.
Check that the
clock shows the correct time of day. Set the I -
- O slide switch to (see Fig. 4) - the convector will switch ON
and OFF according to the timer settings (see Fig 5).
IMPORTANT NOTES
Remember to observe all safety warnings when operating the
heater on auto setting unattended or attended.
If the mains supply to the heater is interrupted, th
e timer clock
will stop until power is restored; reset the time of day to ensure
correct ON and OFF times.
Operation
IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE
PLACED ON THIS HEATER.
Before using the heater ensure that all warnings and
instructions have been read carefully.
OPERATION - SINGLE RATED MODELS
Models DXLWP400, DXLWP400TI, DXLWP800, and DXLWP800TI
N
Turn the heater on using the switch on the right side of the heater
- the switch will be illuminated.
OPERATION - DUAL RATED MODEL - Model ARLWP800TI
The two switches on the side of the heater control the heat output.
Both switches illuminated indicates maximum output.
Top switch only illuminated indicates 500W output on 800W
model.
Bottom switch only illuminated indicates 300W output on 800W
model.
Note: on models fi tted with a timer, at least one switch must be
illuminated for the heater to operate.
MODELS WITH TIMER - (see Fig. 3)
DXLWP400TI and DXLWP800TI N - 1 Switch,
The switch on the side of the heater turns the heater on.
Note: This switch must be in the “on” position before the heater
will operate.
ARLWP800TI - 2 Switches
The two switches on the side of the heater control the amount
of heat available as described above, (Operation - Dual Rated
Model).
NOTE: At least one switch must be in the ‘On’ position before the
heater will operate.
4.00 pm - 9.30 pm
7.00 am - 9.00 am
15
1
1
1
2
4
5
6
8
9
10
7
3
24
1
6
22
23
20
21
18
17
19
1
2
13
14
O
I
Fig. 3
Fig. 5
Fig. 4
11
5
13
12
14
I
O
(5 páginas)
(29 páginas)
(20 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais