Dimplex DABKT15 Manual do Utilizador descarregar pdf (Página 31)

BFH Plint-inbouwventilatorkachels

• Plint-inbouw ventilatorkachels zijn ultieme ruimte-

bespaarders in situaties waar wandruimte beperkt

of volgebouwd is, zoals in keukens, stuurhutten op

schepen en toonbanken in winkels

• Bi-metale thermostaat reageert op lucht-

temperatuur

• Vorstbeveiligingsstand + 5° C

• Bediening op frontpaneel: aan/uit schakelaar

• Thermostaat, regelbaar van ca. 5° C tot 30° C

• Drie vermogensstanden: 0,8 kW, 1,6 kW en 2,4 kW

• ‘Cool air’ ventilatiestand

• Indicatielampje geeft aan of toestel

ingeschakeld is

• Open spiraalelement van hoogwaardige kwaliteit

• Beveiligd tegen oververhitting

• Radiaalventilator staat garant voor een zeer laag

geluidsniveau

• Wordt geleverd met ca. 2m 3-aderige

aansluitsnoer

• Klasse I

• Frontkleuren: BFH24T – wit, BFH24TS - RVS

BUH Plint-inbouwventilatorkachels

• Deze watergevoede plint-inbouwventilatorkachels

zijn speciaal ontwikkeld om in een (bestaand)

cv-systeem een traditionele radiator te vervangen

om zo wandruimte vrij te maken voor andere

toepassingen.

• Toepassingsmogelijkheden zijn o.a. keukens,

receptiedesks, toonbanken en traptreden in een

kleine hal

• Kan een ruimte aanzienlijk sneller opwarmen dan

een vele malen grotere radiator

• Door gebruik te maken van het cv-systeem kan

met een stroomverbruik van slechts 31 Watt

maximaal 2 kW vermogen worden afgegeven.

• Thermostaat schakelt toestel automatisch uit als

de watertemperatuur onder de 38° C zakt.

• Radiaalventilator staat garant voor een zeer laag

geluidsniveau, naar keuze te schakelen op

‘normaal’of ‘boost’stand en kan desgewenst ook

op deze standen een koele luchtstroom

produceren.

• Wordt geleverd met ca. 2m 3-aderig aansluitsnoer

en ﬂ exibele slangen om het toestel op de aan- en

afvoerleidingen van de cv-installatie aan te sluiten.

• Klasse I

• Frontkleuren: BUH19W – wit, BUH19S – RVS

Alle modellen

Indien er een overstek is van meer dan 75mm, dan moet een afstand van tenminste 100mm worden aangehouden

tussen het overstek en het bovenste deel van de verwarming.

Installatie/afmetingen BFH (mm)

Afmeting uitsparing Vooraanzicht

Bovenaanzicht Zijaanzicht

Type Vermogen kW Afmetingen mm (hxbxd)

BFH24T 0,8 - 1,6 - 2,4 120 x 500 x 210

BFH24TS 0,8 - 1,6 - 2,4 120 x 500 x 210

technical specification 43

BFH TECHNICAL SPECIFICATION

BFH BASE UNIT HEATERS

CONTROLS

ALL MODELS:

Thermostat control knob on front of heater with a

temperature range of approximately 5°C to 30°C.

Lowest setting provides frost protection level.

REMOTE CONTROL MODELS

BFH24R/BFH24RB/BFH24RS:

Switch Panel – 13 amp fuse, double pole

isolating switch, two single pole ON/OFF

switches controlling elements.

INTEGRAL CONTROL MODELS

BFH24T/BFH24TB/BFH24TS:

Built-in switches on heater fascia on/off, fan

only. 3 heat settings. Neon indicator.

ELEMENTS – ALL MODELS

Fully strung, helically wound, 800W and 1600W

combine to give 2400W maximum output.

THERMOSTAT – ALL MODELS

Bi-metal type, air temperature sensing.

ELECTRICAL CONNECTIONS

REMOTE CONTROL MODELS:

2.5 metre 6-core colour coded cable is supplied

for connecting the heater to the switch panel.The

installer must supply suitable conduit or trunking if

required and a surface or flush mounting box for

the switch panel. A list of suitable standard boxes

is supplied with the heater.

INTEGRAL CONTROL MODELS:

Supplied with 2m 3 core cable.

THERMAL SAFETY DEVICE

Interrupt supply to reset type.

COLOUR

BFH24T/BFH24R – White

BFH24TB, BFH24RB – Dark Brown

BFH24TS/BFH24RS – Stainless Steel

INSTALLATION

Minimum back box depth of 40mm is required

behind fascia plate.

INSTALLATION/DIMENSIONS (MM)

APERTURE DIMENSIONS

PLAN

FRONT VIEW

SIDE VIEW

ALL MODELS

SWITCH PANEL REMOTE

CONTROL MODELS

Note:

If fitted in corner with adjacent cupboards to

right hand side of heater then a distance of at

least 150mm must be maintained between the

right hand end of the heater and the front of

the adjacent cupboard door as shown.

If the overhang above the heater is greater than 75mm, then a distance of at least 100mm must be maintained

between the overhang and the uppermost part of the heater.

145mm

86mm

Dimp-14957-HeatBook-Oct05 13/10/05 4:33 pm Page 43

technical specification 43

BFH TECHNICAL SPECIFICATION

BFH BASE UNIT HEATERS

CONTROLS

ALL MODELS:

Thermostat control knob on front of heater with a

temperature range of approximately 5°C to 30°C.

Lowest setting provides frost protection level.

REMOTE CONTROL MODELS

BFH24R/BFH24RB/BFH24RS:

Switch Panel – 13 amp fuse, double pole

isolating switch, two single pole ON/OFF

switches controlling elements.

INTEGRAL CONTROL MODELS

BFH24T/BFH24TB/BFH24TS:

Built-in switches on heater fascia on/off, fan

only. 3 heat settings. Neon indicator.

ELEMENTS – ALL MODELS

Fully strung, helically wound, 800W and 1600W

combine to give 2400W maximum output.

THERMOSTAT – ALL MODELS

Bi-metal type, air temperature sensing.

ELECTRICAL CONNECTIONS

REMOTE CONTROL MODELS:

2.5 metre 6-core colour coded cable is supplied

for connecting the heater to the switch panel.The

installer must supply suitable conduit or trunking if

required and a surface or flush mounting box for

the switch panel. A list of suitable standard boxes

is supplied with the heater.

INTEGRAL CONTROL MODELS:

Supplied with 2m 3 core cable.

THERMAL SAFETY DEVICE

Interrupt supply to reset type.

COLOUR

BFH24T/BFH24R – White

BFH24TB, BFH24RB – Dark Brown

BFH24TS/BFH24RS – Stainless Steel

INSTALLATION

Minimum back box depth of 40mm is required

behind fascia plate.

INSTALLATION/DIMENSIONS (MM)

APERTURE DIMENSIONS

PLAN

FRONT VIEW

SIDE VIEW

ALL MODELS

SWITCH PANEL REMOTE

CONTROL MODELS

Note:

If fitted in corner with adjacent cupboards to

right hand side of heater then a distance of at

least 150mm must be maintained between the

right hand end of the heater and the front of

the adjacent cupboard door as shown.

If the overhang above the heater is greater than 75mm, then a distance of at least 100mm must be maintained

between the overhang and the uppermost part of the heater.

145mm

86mm

Dimp-14957-HeatBook-Oct05 13/10/05 4:33 pm Page 43

technical specification 43

BFH TECHNICAL SPECIFICATION

BFH BASE UNIT HEATERS

CONTROLS

ALL MODELS:

Thermostat control knob on front of heater with a

temperature range of approximately 5°C to 30°C.

Lowest setting provides frost protection level.

REMOTE CONTROL MODELS

BFH24R/BFH24RB/BFH24RS:

Switch Panel – 13 amp fuse, double pole

isolating switch, two single pole ON/OFF

switches controlling elements.

INTEGRAL CONTROL MODELS

BFH24T/BFH24TB/BFH24TS:

Built-in switches on heater fascia on/off, fan

only. 3 heat settings. Neon indicator.

ELEMENTS – ALL MODELS

Fully strung, helically wound, 800W and 1600W

combine to give 2400W maximum output.

THERMOSTAT – ALL MODELS

Bi-metal type, air temperature sensing.

ELECTRICAL CONNECTIONS

REMOTE CONTROL MODELS:

2.5 metre 6-core colour coded cable is supplied

for connecting the heater to the switch panel.The

installer must supply suitable conduit or trunking if

required and a surface or flush mounting box for

the switch panel. A list of suitable standard boxes

is supplied with the heater.

INTEGRAL CONTROL MODELS:

Supplied with 2m 3 core cable.

THERMAL SAFETY DEVICE

Interrupt supply to reset type.

COLOUR

BFH24T/BFH24R – White

BFH24TB, BFH24RB – Dark Brown

BFH24TS/BFH24RS – Stainless Steel

INSTALLATION

Minimum back box depth of 40mm is required

behind fascia plate.

INSTALLATION/DIMENSIONS (MM)

APERTURE DIMENSIONS

PLAN

FRONT VIEW

SIDE VIEW

ALL MODELS

SWITCH PANEL REMOTE

CONTROL MODELS

Note:

If fitted in corner with adjacent cupboards to

right hand side of heater then a distance of at

least 150mm must be maintained between the

right hand end of the heater and the front of

the adjacent cupboard door as shown.

If the overhang above the heater is greater than 75mm, then a distance of at least 100mm must be maintained

between the overhang and the uppermost part of the heater.

145mm

86mm

Dimp-14957-HeatBook-Oct05 13/10/05 4:33 pm Page 43

technical specification 43

BFH TECHNICAL SPECIFICATION

BFH BASE UNIT HEATERS

CONTROLS

ALL MODELS:

Thermostat control knob on front of heater with a

temperature range of approximately 5°C to 30°C.

Lowest setting provides frost protection level.

REMOTE CONTROL MODELS

BFH24R/BFH24RB/BFH24RS:

Switch Panel – 13 amp fuse, double pole

isolating switch, two single pole ON/OFF

switches controlling elements.

INTEGRAL CONTROL MODELS

BFH24T/BFH24TB/BFH24TS:

Built-in switches on heater fascia on/off, fan

only. 3 heat settings. Neon indicator.

ELEMENTS – ALL MODELS

Fully strung, helically wound, 800W and 1600W

combine to give 2400W maximum output.

THERMOSTAT – ALL MODELS

Bi-metal type, air temperature sensing.

ELECTRICAL CONNECTIONS

REMOTE CONTROL MODELS:

2.5 metre 6-core colour coded cable is supplied

for connecting the heater to the switch panel.The

installer must supply suitable conduit or trunking if

required and a surface or flush mounting box for

the switch panel. A list of suitable standard boxes

is supplied with the heater.

INTEGRAL CONTROL MODELS:

Supplied with 2m 3 core cable.

THERMAL SAFETY DEVICE

Interrupt supply to reset type.

COLOUR

BFH24T/BFH24R – White

BFH24TB, BFH24RB – Dark Brown

BFH24TS/BFH24RS – Stainless Steel

INSTALLATION

Minimum back box depth of 40mm is required

behind fascia plate.

INSTALLATION/DIMENSIONS (MM)

APERTURE DIMENSIONS

PLAN

FRONT VIEW

SIDE VIEW

ALL MODELS

SWITCH PANEL REMOTE

CONTROL MODELS

Note:

If fitted in corner with adjacent cupboards to

right hand side of heater then a distance of at

least 150mm must be maintained between the

right hand end of the heater and the front of

the adjacent cupboard door as shown.

If the overhang above the heater is greater than 75mm, then a distance of at least 100mm must be maintained

between the overhang and the uppermost part of the heater.

145mm

86mm

Dimp-14957-HeatBook-Oct05 13/10/05 4:33 pm Page 43

technical specification 43

BFH TECHNICAL SPECIFICATION

BFH BASE UNIT HEATERS

CONTROLS

ALL MODELS:

Thermostat control knob on front of heater with a

temperature range of approximately 5°C to 30°C.

Lowest setting provides frost protection level.

REMOTE CONTROL MODELS

BFH24R/BFH24RB/BFH24RS:

Switch Panel – 13 amp fuse, double pole

isolating switch, two single pole ON/OFF

switches controlling elements.

INTEGRAL CONTROL MODELS

BFH24T/BFH24TB/BFH24TS:

Built-in switches on heater fascia on/off, fan

only. 3 heat settings. Neon indicator.

ELEMENTS – ALL MODELS

Fully strung, helically wound, 800W and 1600W

combine to give 2400W maximum output.

THERMOSTAT – ALL MODELS

Bi-metal type, air temperature sensing.

ELECTRICAL CONNECTIONS

REMOTE CONTROL MODELS:

2.5 metre 6-core colour coded cable is supplied

for connecting the heater to the switch panel.The

installer must supply suitable conduit or trunking if

required and a surface or flush mounting box for

the switch panel. A list of suitable standard boxes

is supplied with the heater.

INTEGRAL CONTROL MODELS:

Supplied with 2m 3 core cable.

THERMAL SAFETY DEVICE

Interrupt supply to reset type.

COLOUR

BFH24T/BFH24R – White

BFH24TB, BFH24RB – Dark Brown

BFH24TS/BFH24RS – Stainless Steel

INSTALLATION

Minimum back box depth of 40mm is required

behind fascia plate.

INSTALLATION/DIMENSIONS (MM)

APERTURE DIMENSIONS

PLAN

FRONT VIEW

SIDE VIEW

ALL MODELS

SWITCH PANEL REMOTE

CONTROL MODELS

Note:

If fitted in corner with adjacent cupboards to

right hand side of heater then a distance of at

least 150mm must be maintained between the

right hand end of the heater and the front of

the adjacent cupboard door as shown.

If the overhang above the heater is greater than 75mm, then a distance of at least 100mm must be maintained

between the overhang and the uppermost part of the heater.

145mm

86mm

Dimp-14957-HeatBook-Oct05 13/10/05 4:33 pm Page 43

tot

meer dan

uitsparing

plint

kabel ingang

deze luchtopening

vrijhouden

afstandshouder

Plintverwarming A3.indd 2 08-05-2006 13:58:22

1 2 ... 26 27 28 29 30 31 32 33 34 35 36

Comentários a estes Manuais

Sem comentários

Dimplex DABKT15 Manual do Utilizador Página 31

Comentários a estes Manuais

Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" Dimplex DABKT15